Few things ruin a drone flight faster than unexpected error codes or bad weather. While weather eventually clears on its own, DJI Mini 2 errors usually won’t fix themselves—and ignoring them can keep your drone grounded for good.
This updated guide breaks down every major DJI Mini 2 error code, what each code means, and the exact steps you can take to fix them. Codes are listed numerically so you can quickly search, scan, and troubleshoot the issue you're facing.
Full List of DJI Mini 2 Error Codes
10001, 10016, 10022, 10023
30007, 30008, 30047, 30049, 30050
30055, 30060, 30064, 30085, 30105
30168, 30210, 30224, 30226
40002, 40011, 40012, 40021
180016, 180030, 180031
DJI Mini 2 Error Codes (Detailed Troubleshooting)
Error Code 10001 – Camera Malfunction
Meaning: Hardware failure.
Fix:
-
Restart the drone and controller.
-
If the error persists, contact DJI Support. Camera repair/replacement is required.
Error Code 10016 – Camera Not Calibrated
Meaning: Camera or gimbal requires calibration.
Fix: How to Calibrate Mini 2 Camera/Gimbal
-
Set drone on a level surface.
-
Open DJI Fly App → … (3 dots) → Camera → Gimbal Settings
-
Select Auto Calibrate Gimbal
-
Wait for automatic completion.
If calibration fails → camera likely needs service.
Error Code 10022 – No SD Card
Insert a UHS-I U3 microSD card (SanDisk/Samsung recommended).
Error Code 10023 – SD Card Malfunction
Try the following:
-
Remove and reinsert the SD card
-
Try a different card
-
Swap to a tested UHS-I U3 card
Error Code 30007 / 30008 – No GPS Signal
The drone cannot hover accurately.
Fix:
-
Fly back manually.
-
Land immediately.
-
GPS module may need repair or replacement.
Error Code 30047 – Barometer Initialization Failed
Restart the aircraft and follow on-screen instructions.
Error Code 30049 – GPS Module Error
Restart aircraft and controller.
If unresolved → GPS module likely needs repair.
Error Code 30050 / 30055 – IMU Calibration Required
Often appears after a crash or rough landing.
Fix: Manually Calibrate IMU
-
Open DJI Fly App → … → Sensors → IMU
-
Follow app instructions
-
Calibration takes ~1 minute
Error Code 30060 – Compass Error
Triggered by magnetic interference (indoors, manholes, metal benches, cars).
Fix:
-
Move the drone several meters away
-
Restart and recalibrate compass
Persistent issues may indicate gimbal hardware damage.
Error Code 30064 – Unable to Take Off
Possible causes: obstacles, geofencing, firmware issues, or ESC failure.
Fix:
-
Restart drone + RC
-
Check for firmware updates
-
If issue continues → ESC board replacement may be required
How to Check Firmware
DJI Fly → … → About → Aircraft Firmware → Check for Update
Error Code 30085 – ESC Connection Error
Hardware failure.
ESC must be repaired or replaced. Contact DJI Support.
Error Code 30105 – Navigation System Error
Fix:
-
Move drone away from metal objects
-
Calibrate IMU
If new out of the box → warranty replacement.
Error Code 30168 – Aircraft Power Insufficient
Causes:
-
Strong winds
-
Aged or failing battery
-
ESC issues
Try switching batteries; inspect for wind conditions.
Error Code 30210 – Power System Hardware Error
Restart drone and controller.
If issue remains:
-
Update drone, RC, and battery firmware.
Error Code 30224 – Incompatible Firmware
Fix:
-
Update all batteries + aircraft firmware
-
Clear app cache:
Profile → Settings → Clear Cache -
Restart DJI Fly App
-
Reinstall app if needed
If still unresolved → DJI service required.
Error Code 30226 – Start Failed
Restart aircraft, controller, and DJI Fly App.
Error Code 40002 – Gimbal Stuck
Usually caused by leaving the gimbal cover on during startup.
Fix:
-
Remove gimbal cover before powering on
-
Ensure the gimbal can move freely
Repeated obstruction can burn out the gimbal motor.
Error Code 40011 – Gimbal Calibration Error
Fix:
-
Run Auto Gimbal Calibration
-
Restart
-
If still unresolved → gimbal replacement required
Error Code 40012 – Gimbal Unable to Connect
Gimbal hardware failure.
Replacement required.
Error Code 40021 – Gimbal IMU Data Error
Gimbal IMU failure.
DJI Support or repair shop recommended.
Error Codes 180016 / 180030 / 180031 – Sensor Errors
Restart drone and controller.
If still present → flight sensors must be replaced.
Final Thoughts
Most DJI Mini 2 error codes can be fixed through calibration, restarting, or firmware updates. However, hardware-related issues—especially camera, gimbal, GPS, ESC, and sensor failures—require professional repair.
Keeping firmware updated, avoiding magnetic interference, and removing the gimbal cover before startup can prevent many common errors.
